My boat has been parked  4 about a year 

sushi

New member
My boat has been parked  4 about a year  and a half. Decided to get it back in the water and when i took it 4 a service i was told  it woulld need a buoyancy inspection as well and if  not satisfactory would need to be sorted out and this would cost abt 5 grand. i dont understand. never had a problem before. i think i might be getting ripped off.

Can adocument.write('/images/emoticons/f5.gif');nyone advise me!!!!
 

Fishton

Sealiner
Any public water, and yes, dams too, requires that you have a bouyancy certificate, certificate of fitness (for your craft), and a you must have a minimum category R skipper's ticket.
 

Royden

Senior Member
I did mine recently myself. Including the certificate cost me R680 - 00. PM me and I will give you my contacted details and explain it to you.
 
Fishton wrote:
Any public water, and yes, dams too, requires that you have a bouyancy certificate, certificate of fitness (for your craft), and a you must have a minimum category R skipper's ticket.

cat C licence is what is needed to go deep sea fishing ..cat R is for inland and single powered crafts not going more than one nautical mile out to sea..
 

mo-manack

New member
what size boat do you have? the actual boyancy itself where they cut and remove n replace old bottles and foam is costly but it has to be done to get seaworthy,i think you need 65 or 75% bouyancy for deep sea n less for dam and bay..5grd doesnt sound bad for your 16ft,i just got mine done last week,it cost 7500,bottles and foam whith inspection covers n i have a 19ft.they cut the deck in certain places n do the bouyancy,then put it all back together again n make it like new..i guess its for our own safety so that if she capsizes of hull get punctures she still floats.
 

Waverunn3r

New member
Hi

Can anybody tell me how would would they inspect the buoyancy on a boat if there's no inspection hatch?
We're going to be send our boat for COF in the next week or so, and the only thing we have to prove that there is some sort of buonacy is the piece of paper we got with the boat. I wanted to cut a inspection hatch, but i'm bang i cut into a cross member or something.
 

Royden

Senior Member
GO TO http://www.samsa.co.za or http://www.samsa.org.za and read the regulations! CAT R 30% required, all other 60%. You guys are getting ripped off with those prices.

http://www.goodhopepowerboatacademy.co.za/samsa_documents/Buoyancy%20of%20Small%20Vessels%20Brochure.pdf

1. Foam costs R 400 + Vat per(1x5L part A and 1 x 5L part B) Which make about 300 - 350L foam! 1L of foam = 1kg bouyancy!
2.SAMSA can survey your boat for you for about R350-00(Undercorrection).


This whole bouyancy thing is just a money making scheme that all the boat shops has jumped onto the band wagon!!!
 

sushi

New member
hve a 16 foot cathedral hull cabin with a 40 mercury motor. boat shop guys cut an inspection hole and reckon that the bottles already in there r not suitable??/ they reckon it needs to be filled with 'high density bottles" . Showed me one of the required bottles--looked like an empty plastic brake fluid bottle to me.

i reckon royden hit the nail on the head when he says we r getting ripped of. could probably diy for 1/4 of the price.
 

Royden

Senior Member
Hi Sushi.

 

I also have a catedral hull boat. Cut holes in the deck and removed the bolts(+-350).30% were water logged already. Thats why I went the foam route.Bouyancy is easy to calculate. Here an example of what I done to apply and some pics of the holes in the deck.
 

Attachments

  • 100_2284.jpg
    100_2284.jpg
    35.8 KB · Views: 235

Fishton

Sealiner
I also started mine yesterday as the due date is just around the corner.

2z6rxuq.jpg


1. Removed seats and hatches
2. Stripped carpet (not essential - mine was old)

2w6gcd1.jpg


3. Bought a paint stirrer (R24) from Builders Express, some measuring jugs and a mixing jug (2.5l) (R70 for all) from Game, 4 inspection hatches (R70 each) from Natal Sprite, 2 x 5l foam (R400) from RigiFoam in Pinetown and some disposable gloves.

2zrmdmv.jpg


4. Marked and cut out holes in deck with skill saw (jig saw) - remember to measure length of blade first so you don't hit the hull.

f44sb8.jpg


5. Inspect hull for obstructions and/or moisture

5m04uh.jpg


6. Measure foam EXACTLY in seperate containers and stir for 15 seconds on high speed.

348ledg.jpg


7. As I started with the bow section, I had to drop the nose of the boat by lowering the jockey right to the ground so the foam can run to the bow.

hunmeb.jpg


8. Repeat on Port side

And that's as far as I've got.  This all took me just over an hour so far (and 2 hours of shopping :()

To be continued .....
 

Royden

Senior Member
Hi Fishton.

 

Well done so far! Before you close the holes, get a SAMSA surveyor to inspect to ensure they are happy with the volume. Once holes are closed they need to inspect again. Normally about R350-00 for both inspections.
 

Fishton

Sealiner
Royden wrote:
Hi Fishton.

 

Well done so far! Before you close the holes, get a SAMSA surveyor to inspect to ensure they are happy with the volume. Once holes are closed they need to inspect again. Normally about R350-00 for both inspections.
Will do Royden, thanks for the advice.
 

sushi

New member
Hi Royden

Lekker boat u hve there. Mine is very similar except that it has a closed cabin.

Thx a milion 4 the advice. congrats, very professionally done. i am sure its going to help a lot of sealiners who hve the same problem.

Thx also 4 the contact details. Will definitely be in touch with u soon.

btw how do u close the holes once the foam has been inserted and does this foam meet SAMSA requirements in that it should not be affected by oil, water ect.
 

Royden

Senior Member
Hi Sushi

 

As the foam was rising close to the deck, I placed the cut out back into position with a board covering over that, keeping the cut out level with the deck. Once all settled, poured resin ontop to seal and the added 2 layers of fiberglass and resin. You cant see where it was done once painted.
 

Patrick

Sealiner
Waverunn3r wrote:
Hi

Can anybody tell me how would would they inspect the buoyancy on a boat if there's no inspection hatch?
We're going to be send our boat for COF in the next week or so, and the only thing we have to prove that there is some sort of buonacy is the piece of paper we got with the boat. I wanted to cut a inspection hatch, but i'm bang i cut into a cross member or something.
Hi. If your boat already has a flotation certificate, or paper, then that will suffice for the COF survey. The person that surveys your boat for category rating doesnt check your hull for flotation. That is done elsewhere if you dont have the flotation cert already. So there is no need to cut an inspection hatch in your deck now if you already have the flotation cert.  As you say, without the boat plans you may cut through a stringer or bulkhead and weaken the deck. Besides, i think inspection hatches are just another possible point of entry for water to leak into your hull and begin to rot your deck.
 
Top