SEALINE - South African Angling and Boating Community Home 
Home Recent Search search Menu menu Not logged in - Login | Register


 Moderated by: Emperor
New Topic Reply Printer Friendly
daiwa sealine 900h/910h rebuild  Rating:  Rating
 
AuthorPost
 Posted: Sun Feb 8th, 2009 05:46 am
  PM Quote Reply
1st Post
alantani
Senior Member


Joined: Tue Dec 18th, 2007
Location: Saratoga, California, California USA
Posts: 153
Equipment: accurate reels, calstar rods, blackwater spectra (soon to be prostaff)
Best Catch: my wife, 5'2", 125 pounds
Favorite Fishing Spot: northern california coast
Boat: grady white 258
Club: 
Status: 
Offline
Mana: 
as old they are, the daiwa 900h and 910h are still very popular among big fish fishermen.  here's your reel.



what were going to do is change out the old 3-stack of drag washers to a new 5-stack of carbon fiber with thinner metal washers. 



we're going to install a bigger handle grip.



and change out the rod clamp.



first, let's back out each one of the left side plate screws (key #'s 2 and 3).



note that the three screws on top are shorter than the two screws on the base.



add a bead of grease to each screw hole and zip the screws back in.



now, lets back out all of the right side plate screws (key #'s 51 and 52).



the reel separates easily into three pieces, the spool, frame and right side plate.



lube the left side plate bearing.



take an old toothbrush and clean up the inside of the frame.



i'm going to install a 6/0 penn graphite clamp.





ok, the frame is done.



let's clean up the spool a little.



and back into the frame it goes. 



now, on to the right side plate.



remove the handle lock screw (key #66).



remove the handle handle screw (key #65) using a a handle wrench from a shimano tld 20/30 two speed.





remove the handle (key #64).



remove the handle washer (key #63).



remove the star drag (key #62).



remove the spacing sleeve (key #61).



remove the tension springs (key #58 and 60) and drag spring washer (key #59).



back out the three set plate screw A's (key #45) and set plate screw B (key #46).



the set plate assembly (key #29) will drop out as a unit.



here's the old stack of drag washers compared to the new stack.



here's the height of the old drag stack.



here's the height of the new stack.



slap a thick coat of cal's drag grease on every carbon fiber drag washer and rebuild the drag stack.







install the spacing sleeve (key #61).


place two fingers over the four set plate screws.





the set plate should lay down cleanly into the right side plate.





flip the right side plate over.



tighten down the set plate screws (key #'s 45 and 46).



install the tension springs (key #58 and 60) and drag spring washer (key #59).





install the star drag and turn it down until it is well past the shoulders of the drive shaft.



install the handle washer (key #63).



now to switch out the smaller stock grip for a larger kolekar grip.  first, let's drill out the rivet.









the new grip bolts right on.



tighten down the handle screw (key #65) using the shimano wrench.



install the handle lock screw (key #66).



the right side plate is done.



lube the spool shaft.



lube the set plate bearing (key #28).



install the right side plate assembly.



install the right side harness lug (key #18) and rod brace lug (key #19).



install the right side plate screws (key #'s 51 and 52).



so here is our completed reel. you now have a full sized handle grip, a stack of 6 penn drag washers (1+5) and a new clamp.  the driving force behind this rebuild was the need to increase the drag range of this reel.  a  stack of four drag washers (1+3) only delivers 20 pounds of drag.  that is way too low for a reel this large.  by cutting thinner metal drag washers, i could use a set of five #6-116 penn ht-100 drag washers inside the gear and a single #6-114 drag washer underneath the gear. this stack of drag washers will deliver 30 to 35 pounds of drag, bringing the reel up to it's full potential. 



to convert a sealine 910h to a 900h, you need a 900h set plate (part #783-3302), a 900h handle screw (part #781-2301), a handle set screw (part #353-2811) and a 900h handle (part #748-1101).  you can call daiwa at 562-802-9589 and order these parts.  the total should be somewhere around $30.  add to that a 6/0 kolekar grip for $33 http://alantani.com/index.php?topic=158.0 and a drag washer set for $25 http://alantani.com/index.php?topic=153.0



the other alternative is to cut the handle arm of the 910h a little shorter.  the set plate for the 910h is quite a bit shorter than the 900h.





there you go.  great reel, and a much better value than the 9/0 penn senator 115L. 



 


 

Last edited on Sun Feb 8th, 2009 06:18 am by alantani

Back To Top PM Quote Reply  

 Posted: Thu Jun 7th, 2018 01:41 pm
  PM Quote Reply
2nd Post
rylater86
Member


Joined: Thu Jul 5th, 2012
Location: Durban,amanzimtoti, South Africa
Posts: 58
Equipment: blue marlin G3,torium 30,frank and loomis custom built,torium 30,penn fathom ...
Best Catch: 18kg daga salmon
Favorite Fishing Spot: nyoni rocks,chain rocks,isipingo
Boat: n/a
Club: n/a
Status: 
Offline
Mana: 
Where can one purchase the complete washer upgrade in south Africa?

Back To Top PM Quote Reply

 Posted: Thu Jun 7th, 2018 03:58 pm
  PM Quote Reply
3rd Post
Dr halibut hoffman
Sealiner


Joined: Wed Sep 16th, 2009
Location: Cape, South Africa
Posts: 1930
Equipment: Shimano, daiwa, a finnor and an elbe.. The rest died.
Best Catch: 145cm FL Leervis released (Shore), 80 something kg yellowfin (Boat). ... ...
Favorite Fishing Spot: Capes, kranse en die diepsee!
Boat: 15' Skicraft cat and crew on a Buttcat.
Club: Prefer Ike jime to club
Status: 
Offline
Mana: 
My Gallery: 
Can you not order online?
http://www.smoothdrag.com/

Back To Top PM Quote Reply  

 Posted: Thu Jun 7th, 2018 04:16 pm
  PM Quote Reply
4th Post
PietervdM04
Member


Joined: Sun Sep 10th, 2017
Location: Roodepoort, South Africa
Posts: 18
Equipment: Saltiga, Trinidad, Purglass
Best Catch: Raggie, 216cm, 189kg
Favorite Fishing Spot: Struisbaai
Boat: No
Club: JHB Coastal Angling
Status: 
Offline
Mana: 
I ordered direct from Alan Tani after I saw it on his site.
I mailed him and he replied that he can post it.
My wife had to help with all the Computer stuff and the payment online.
I received the handle and drag upgrade and fitted it, no problem.

Back To Top PM Quote Reply


Current time is 12:35 am  
SEALINE - South African Angling and Boating Community > General Angling Topics > Reel Servicing and Maintenance Guides > daiwa sealine 900h/910h rebuild Top